
| Material | 3000W | 6000W | 12000W |
| Carbon steel | 1-10 mm | 1-16 mm | 1-25 mm |
| Stainless steel | 1-5 mm | 1-8 mm | 1-13 mm |
| Aluminum | 1-4 mm | 1-6 mm | 1-10 mm |
| Galvanized steel | 1-4 mm | 1-6 mm | 1-10 mm |
Recommended thickness range for production cutting with clean edges. Higher power 20000W / 30000W / 40000W available on request. Actual results vary with material quality, assist gas and required edge finish.




|
TECHNICAL PARAMETERS |
||||||
| Machine Model | KC8025 | KC12025 | KC13032 | KC16032 | KC24032 | KC34032 |
| Working Area | 8000mm*2500mm | 12000mm*2500mm | 13000mm*3200mm | 16000mm*3200mm | 24000mm*3200mm | 34000mm*3200mm |
| Laser Power | 3000W/6000W/12000W/20000W | 6000W/12000W/20000W/30000W | 6000W/12000W/20000W/30000W | 12000W/20000W/30000W | 12000W/20000W/30000W/40000W | 6000W/12000W/20000W/30000W/40000W |
| X/Y Pos. Accuracy | ±0.03mm | ±0.03mm | ±0.03mm | ±0.03mm | ±0.03mm | ±0.03mm |
| X/Y Rep. Pos. Accuracy | ±0.02mm | ±0.02mm | ±0.02mm | ±0.02mm | ±0.02mm | ±0.02mm |
| Max. Linkage Pos. Speed | 110m/min | 110m/min | 110m/min | 110m/min | 110m/min | 110m/min |
| Max. Acceleration | 1.5G | 1.5G | 1.5G | 1.5G | 1.5G | 1.5G |
| Rated Volt. & Freq. | 3PH 380V 50Hz | 3PH 380V 50Hz | 3PH 380V 50Hz | 3PH 380V 50Hz | 3PH 380V 50Hz | 3PH 380V 50Hz |
Q: What plate lengths can this machine cut?
A: The standard lineup runs from 8000 × 2500 mm (KC8025) to 34000 × 3200 mm (KC34032). Because the gantry runs on ground rails rather than a fixed bed, the track can be extended on site for plates longer than 34 m.
Q: What is the difference between this machine and the segmented bed large-format machine?
A: The segmented bed machine joins modular bed sections into one rigid table. This machine removes the bed from the length equation: the workpiece sits on the floor-level support and the gantry travels along ground rails, so track length can grow with your plates.
Q: What thickness can it cut?
A: With a 6000W source the recommended range is 1-16mm carbon steel and 1-8mm stainless steel; with 12000W it rises to 1-25mm carbon steel and 1-13mm stainless steel. Power up to 40000W is available for heavier plate.
Q: What laser power options are available?
A: 3000W to 40000W depending on the model. Long frames such as KC24032 and KC34032 are normally specified with 12000W and above.
Q: What accuracy and speed can the machine achieve?
A: X/Y positioning accuracy ±0.03mm, repeat positioning accuracy ±0.02mm, maximum linkage speed 110m/min and maximum acceleration 1.5G, held across the full rail length.
Q: How is the gantry kept stable over such a long travel?
A: A lightweight integrated beam reduces inertia and vibration, and a dual-motor synchronous drive on both rail sides keeps the two ends of the gantry balanced, so the beam stays square over the whole track.
Q: Can it cut bevels for welding preparation?
A: Yes, with the optional 3D bevel head. It tilts ±45° and completes V, X, Y and K bevels in a single pass, which removes the need for secondary grinding on thick plate.
Q: Can the track be extended after the machine is installed?
A: Yes. The rail system is modular, so additional rail sections can be added on site later when your plate length increases, without replacing the gantry or the machine.
Q: What is the price, delivery time and can I test my material?
A: Price depends on track length and laser power, and delivery is normally 30-40 days after deposit. Sample cutting tests are available — send your material, thickness and plate length for a quotation and a test arrangement.